Equipment

The Static Load Tester (SLT) automatically obtains and records reliable readings at programmable load intervals during a static load test.

The Pile Driving Monitor (PDM) uses optically safe infrared lasers to track a disposable reflective sticker adhered directly to the pile.

The Pile Driving Analyzer (PDA) system is the most widely employed system for Dynamic Load Testing and Pile Driving Monitoring in the world. PDA tests assess the capacity of several piles in a single day.

Length Inductive Test Equipment (LITE) evaluates the length of existing steel piles (Steel Sheet Piles, H-piles, Pipe piles, Cased Drilled Shafts, and highly reinforced Drilled Shafts) using the inductive field method.

GRLWEAP is a one-dimensional Wave Equation Analysis program that simulates the pile response to pile driving equipment.

E-Saximeter registers all relevant pile driving parameters. It calculates the hammer operating rate in blows per minute and helps the piling inspector create a pile driving log.

CAPWAP® (Case Pile Wave Analysis Program) is the industry state-of-practice tool to establish the pile capacity, and estimates total bearing capacity of a pile or shaft, as well as resistance distribution along the shaft and at the toe.

The Thermal Integrity Profiler (TIP) uses the heat generated by curing cement to assess the quality of drilled shafts and of bored, augered cast in place, continuous flight auger or drilled displacement piles.

The Static Load Tester (SLT) automatically obtains and records reliable readings at programmable load intervals during a static load test.

The Shaft Quantitative Inspection Device (SQUID) system is a new technology for quantitatively assessing the quality of the bottom surface of a bored pile or drilled shaft.

SHAPE is a cost-effective quality assurance testing device used for deep foundations such as drilled shafts, slurry walls, barrettes and more to determine the excavation dimensions and verticality.

The Pile Integrity Tester (PIT) gives peace of mind that a pile or shaft is free of major cracks and voids, prior to construction of the superstructure.

The Pile Dynamics Analyzer – Dynamic Load Tester was designed specifically for quality assurance testing of drilled shafts and bored piles.

The Pile Driving Analyzer (PDA) system is the most widely employed system for Dynamic Load Testing and Pile Driving Monitoring in the world. PDA tests assess the capacity of several piles in a single day.

PDI-TOMO is a 3D tomography imaging tool that supplements the CHAMP output. It analyzes wave speeds (derived from arrival time data from the scans of all pairs of tubes) to yield a wave speed map of the entire shaft volume.

The Cross-Hole Analyzer determines the quality and consistency of the concrete of drilled shafts, slurry walls, bored piles, cast-in-situ piles and other types of concrete foundations. It is ideal for testing four probes in one go, thus, saving time and money. CHAMP-Q has colour coded wires for easy identification of probe receiving/transmitting.

CAPWAP® (Case Pile Wave Analysis Program) is the industry state-of-practice tool to establish the pile capacity, and estimates total bearing capacity of a pile or shaft, as well as resistance distribution along the shaft and at the toe.

The Thermal Integrity Profiler (TIP) uses the heat generated by curing cement to assess the quality of drilled shafts and of bored, augered cast in place, continuous flight auger or drilled displacement piles.

The Pile Integrity Tester (PIT) gives peace of mind that a pile or shaft is free of major cracks and voids, prior to construction of the superstructure.

The Pile Installation Recorder (PIR) is an Automated Monitoring Equipment that assists in the correct installation of augered cast in place (ACIP) / continuous flight auger (CFA) and drilled displacement piles by displaying target versus actual poured concrete volume in real time.

The Pile Driving Analyzer (PDA) system is the most widely employed system for Dynamic Load Testing and Pile Driving Monitoring in the world. PDA tests assess the capacity of several piles in a single day.

CAPWAP® (Case Pile Wave Analysis Program) is the industry state-of-practice tool to establish the pile capacity, and estimates total bearing capacity of a pile or shaft, as well as resistance distribution along the shaft and at the toe.

The Thermal Integrity Profiler (TIP) uses the heat generated by curing cement to assess the quality of drilled shafts and of bored, augered cast in place, continuous flight auger or drilled displacement piles.

TEMP (Thermal Evaluation of Mass Pours) is a system that measures temperatures in various points of a mass concrete pour, as the curing cement generates heat.

The SPT Analyzer measures the energy transferred into an instrumented SPT rod during a Standard Penetration Test (SPT).

The Pile Integrity Tester (PIT) gives peace of mind that a pile or shaft is free of major cracks and voids, prior to construction of the superstructure.

The Pile Driving Analyzer (PDA) system is the most widely employed system for Dynamic Load Testing and Pile Driving Monitoring in the world. PDA tests assess the capacity of several piles in a single day.